Aerial view of an industrial estate with large warehouses, solar roofs and truck hardstand
Industrial leasing

Warehouse and industrial leasing in NSW

To lease a vacant warehouse in NSW, put the right operators in front of the space with the rent and terms settled before anyone is approached. Blox Commercial agrees the rent, term and incentive with you in writing, builds a shortlist of trades, logistics, manufacturing and wholesale operators, then approaches them with the specification they decide on: clear height, power, loading, access, hardstand and zoning. The same team can manage the tenancy once it is signed. Occupiers looking for space can tell us what they need using the requirements builder below.

Prefer to talk? Call 02 8883 4559

  • NSW Licence 10103554Blox Property Group Pty Ltd
  • Terms in writingbefore any operator is approached
  • One teamfrom lease to management
For landlords

How do you lease a vacant warehouse in NSW?

Start with what operators decide on, then run the campaign in a fixed order.

  1. 1
    Inspect and specifyWe record clear height, power, floor loading, loading, access and hardstand, and check the zoning suits the likely uses.
  2. 2
    Agree terms in writingRent, term, incentive and review method are settled with you before any approach.
  3. 3
    Shortlist operatorsTrades, logistics, manufacturing and wholesale operators whose needs match the space.
  4. 4
    Approach and negotiateWe approach the shortlist, run inspections and negotiate to the terms you approved.
  5. 5
    Document and hand overYour solicitor drafts the lease. The same team can manage the tenancy after it starts.
Empty warehouse interior with polished slab, steel portal frame and roller doors
The specification

What do industrial tenants look for?

Operators match the specification to how they run before they talk rent.

Row of loading dock doors with dock shelters on an industrial building
Metres

Clear height

Measured to the underside of the lowest structural member. It limits racking and stacking.

Amps

Power

Supply capacity, and whether it is single or three phase. Manufacturing needs more than storage.

Doors and docks

Loading

Ground level roller doors, dock high loading or both, and room for trucks and forklifts.

Vehicles

Access

Truck access and turning for the fleet the operator runs, and the route to the arterial road.

Square metres

Hardstand

Yard area for parking, trucks and storage, its surface and drainage, and how much is included.

Consent

Zoning

Whether the operator's use is permitted at the address, with or without consent. Council confirms.

Lease types

What is the difference between a warehouse, factory and industrial unit lease?

The documents look alike. The uses differ, and so do the clauses that matter.

PointWarehouseFactoryIndustrial unit
Typical useStorage, distribution and fulfilmentMaking, processing and assemblingSmaller space for trades and light industry
Clauses that matterClear height, racking, loading and hours of operationPower and services, approvals for the process, and removal of fixed plantShared driveways, owners corporation rules and parking
Landlord's questionDoes the building suit the loading pattern?Are the approvals and services in place?Does the common property work for the tenant's vehicles?
Rent

How are industrial rents set and reviewed?

Industrial rent is quoted as a rate per square metre per year, with outgoings added where the lease provides for them. The rate reflects comparable leases, the specification and the term.

Fixed increase

A set increase on each review date, written into the lease.

CPI review

The rent moves with the Consumer Price Index. The CPI calculator works out the increase.

Market review

The rent is reset to market at a review date. Our guide to market rent review explains the process.

The Retail Leases Act 1994 (NSW) covers retail shop leases. The NSW Small Business Commissioner explains how to check whether premises are covered, and says the Act may apply even if the agreement says otherwise. A solicitor should confirm for any lease.

Aerial view of warehouses with large hardstand areas beside a highway
Yards

What about yards and hardstand?

A yard or hardstand can be leased with a building or on its own. Operators use them for trucks, containers, equipment and outdoor storage. The area is the whole value, so the lease needs to be exact about it.

  • Surveyed area and boundaries
  • Surface and load capacity
  • Drainage and stormwater
  • Fencing, gates and security
  • Lighting and hours of use
  • Truck access and turning
  • Permitted use and zoning
  • Who repairs the surface
End of lease

What is make good on industrial premises?

Make good is the tenant's obligation at the end of the lease to return the premises to the condition the lease requires. On industrial premises that can include removing racking, mezzanines and fixed plant, repairing the slab and doors, and clearing the yard.

The lease should state the standard clearly, and a dated condition report at the start gives both sides a fair reference. Make good on industrial premises is set out in the lease; Blox schedules it from the first inspection.

For occupiers

What space are you looking for?

Pick what applies. The brief on the right writes itself and goes into the enquiry form.

Use choose any
Floor area
Clear height
Power
Loading choose any
Locations choose any
Timing
industrial property managementRent, outgoings, inspections and lease dates after the tenant is in.
warehouse property managementManagement for warehouse and distribution assets.
commercial leasing agentsLeasing for retail, large format, QSR, medical and industrial.
Common questions

Industrial leasing questions

Do you lease warehouses for tenants as well as landlords?

Landlords come first: we are appointed to lease the property. Occupiers looking for space can send a brief using the requirements builder on this page, and we match it to the space we are leasing.

How long does it take to lease a vacant industrial unit?

It depends on the condition of the unit, the rent, the specification and the zoning. We agree rent and terms with you in writing before any operator is approached, which removes the most common delay.

Can a yard or hardstand be leased on its own?

Yes. A yard or hardstand can be leased with a building or separately. The lease needs to state the area, the permitted use, access for trucks, drainage and who repairs the surface. A solicitor confirms the document.

Who looks after the property after it is leased?

The same team can manage the tenancy: rent collection, outgoings, inspections and the lease dates. See our industrial property management and warehouse property management pages.

Enquire

Tell us about the space

Landlords: send the address and what is vacant. Occupiers: use the brief above or write your own.

02 8883 4559[email protected]14-16 Brookhollow Avenue, Norwest NSW 2153

Already leased? Our industrial property management team can take over the tenancy.

Tell us about the property or what you need. A Blox leasing agent will be in touch.

Enquiry type
Add your name.
Add an email we can reply to.

Your enquiry goes to the Blox leasing team.

Thanks. We will be in touch.

Your enquiry has gone to the Blox team.

Call 02 8883 4559 Enquire